- How To Use Auto Tune For Megasquirt Iii 1
- How To Use Auto Tune For Megasquirt Iii 2
- Megasquirt Self Tuning
Application(s): 1990 to 1996 Nissan 300ZX VG30DE and VG30DETT motors with the OEM distributorless ignition.
That'll make it hard to tune. Your LC-1 should be set for 0-5v = 10-20 AFR and EGO Switchpoint at 2.35v. Step is the amount of each change. Limit should be max 10% - but try 5 to start and increase if necessary. AutoTune is not magic, but rather a helpful aid to proper tuning. Besure to read the sections on AutoTune so you know how to use it properly. Update Controller checkbox - (Only Available on some firmwares such as MegaSquirt 3.) When checked, WUE Analyze will update the controller periodically with the recommended values. It will act as if you are pressing the Apply button. Apply Button - When clicked, the recommended values will be written to the controller.
Level of control: Full Standalone EMS– Fuel and Ignition Control
Cookn x3 download. The cam angle sensor has often been a bit of an issue for MegaSquirt, but now with MS3’s new V1.1 code, you don’t have to disassemble the CAS for an alternate trigger wheel – you can use all stock hardware!
ECU Modifications
We recommend the MegaSquirt-III for its support of the stock cam angle sensor. Roland m1 vst crack full.
Using the MS-III PCBv3.0 or V3.57 ECU with MS3X
That’s it! |
Wiring
How To Use Auto Tune For Megasquirt Iii 1
Usually, the MS3 uses pin 32 for the cam input signal. Because of the high frequency of the stock CAS, you’ll be using PT4 (pin 31) instead.
CAS pin out
Pin | Purpose |
A | Low Resolution Signal (MS Pin 24) |
B | High Resolution Signal (MS3X pin 31) |
C | 12 volt power |
D | Ground |
How To Use Auto Tune For Megasquirt Iii 2
You will also need to connect 1K ohm, 1/4 watt resistors from TPS VREF (pin 26) to both the low resolution signal and the high resolution signal to provide a pull-up in the wiring harness.
For the fuel and spark outputs, use the following pins. You can wire the MS3X outputs to the stock ignition module; it will not drive the coils directly.
MS3X injector pin | MS3X spark pin | Letter | Cylinder |
19 | 14 | A | 1 |
16 | 33 | B | 2 |
13 | 15 | C | 3 |
10 | 34 | D | 4 |
7 | 35 | E | 5 |
4 | 36 | F | 6 |
These engines use PWM idle control and boost control, both of which can be done using the MS3X medium current outputs.
TunerStudio Configuration for MS-III
Under the ignition setup menu, set the following.
- Spark mode: Nissan RB25 (We’ve confirmed the VG30DE / DETT CAS has the same pattern)
- Trigger Angle / Offset: 0 (adjust as needed if your timing doesn’t line up)
- Ignition input capture: Rising edge
- Spark output: Going High / Inverted if using stock ignition module
- Number of coils: Coil on plug
- Spark hardware in use: MS3X spark
- Cam input: MS3X
If you use someone else’s .msq file we do recommend you check the firmware version the .msq file was built on as you cannot always use a file built on one firmware version with an ECU running a different version– it’s best to use the .msq files with the same version of the firmware that the file was built on. Alternately you can manually copy the settings over from the borrowed file.
Megasquirt Self Tuning
Suggested parts
Korg m1 le vst download. As stated above, we recommend a MegaSquirt-III V3.0 or V3.57 to have full control over the engine. You will be able to use your existing sensors except for the MAP sensor which is built into the MegaSquirt.
ECU options:
- MegaSquirt-III V3.0 kit and MS3X
- MegaSquirt-III V3.57 assembled unit with MS3X
Other recommended parts
- JimStim Stimulator kit or assembled JimStim
- 12′ wiring harness and 12′ MS3X add on harness (8′ also available)